After drilling, put the screws
2018年8月6日However, even though this trick is one of the oldest tricks ever, some say that this will only create more damage to the game console especially if it is done repeatedly.
Another method for Xbox 360 repair is a little tedious but more effective than the towel trick. Then that was the end of your game and possible the end of your console.
After drilling, put the screws back and tighten them slowly. In using the hand drill though, a block of wood should be placed beneath each hole to make sure that the metal case would not be harmed or warp. The best way to fix this dilemma is to bring it back to where you bought it but that is if it is still covered by its warranty. Remember that the four holes on the left side of the game board are for the GPU screws while the holes on the right are for the screws of the CPU.
The concept behind this trick is to heat the game box so that the soldering which attaches the board together will melt and bring back the connection. The Red Ring of Death is a common problem for Xbox 360 that needs immediate attention. After the screws have been screwed completely, it is time to put back the heatsinks.
. Doing this thing can probably help because it was thought that what causes the Red Rings are loosening of the computer board that it needs to be http://www.cncentrifugalswitch.com/ retightened again. After everything has been cleaned, make 8 screw holes on spots where the original x clamps are positioned and push a 3/16 drill equipped with a drill press to re hole the holes. These x clamps should be carefully taken off by using a wrench or a nut driver. Also before placing back all the components together, be sure that the shiny silver things found in the CPU and GPU should be wrapped with thin thermal paste first to avoid loosening. The procedure is simple and you just need to turn the Xboxs power off, remove the game CD and unplug the network cable while leaving the power cord open. Recommended screws to use are 5x20MM and 5x15 Panhead Machine Screws and you can buy them in any hardware. Use a metal scrubber to remove all of the thermal junks on the heatsinks. Fortunately, now that there are online tutorials that will actually teach you to repair electronics including game consoles, the internet is also having tutorials on Xbox 360 repair.
Afterwards, try checking if the repair works by plugging it on the AV power cable and plugging the console on the RF board. Accordingly, one of the most common methods in resolving the Red Ring of Death is using the towel trick. After about few seconds, turn the power on again and have the game box wrapped in 3 or more towels. The first thing you have to do is removing the heatsinks of the game console by taking off the two x shaped clamps that holds the motherboard. Reinstall the screws on their respective places and make sure that they are not too tight or too loose. Once the heatsinks are removed, all the other parts should be separated from the metal case and the motherboard placed in a clean place. If not then you have to shell out some money and find a person who can fix your console.You are having a good time with your Xbox and with just few seconds away from finishing your game when suddenly the dreaded Red Ring of Death started flashing. If you do not have this kind of drill you can also use a hand drill to make the holes bigger.
Another method for Xbox 360 repair is a little tedious but more effective than the towel trick. Then that was the end of your game and possible the end of your console.
After drilling, put the screws back and tighten them slowly. In using the hand drill though, a block of wood should be placed beneath each hole to make sure that the metal case would not be harmed or warp. The best way to fix this dilemma is to bring it back to where you bought it but that is if it is still covered by its warranty. Remember that the four holes on the left side of the game board are for the GPU screws while the holes on the right are for the screws of the CPU.
The concept behind this trick is to heat the game box so that the soldering which attaches the board together will melt and bring back the connection. The Red Ring of Death is a common problem for Xbox 360 that needs immediate attention. After the screws have been screwed completely, it is time to put back the heatsinks.
. Doing this thing can probably help because it was thought that what causes the Red Rings are loosening of the computer board that it needs to be http://www.cncentrifugalswitch.com/ retightened again. After everything has been cleaned, make 8 screw holes on spots where the original x clamps are positioned and push a 3/16 drill equipped with a drill press to re hole the holes. These x clamps should be carefully taken off by using a wrench or a nut driver. Also before placing back all the components together, be sure that the shiny silver things found in the CPU and GPU should be wrapped with thin thermal paste first to avoid loosening. The procedure is simple and you just need to turn the Xboxs power off, remove the game CD and unplug the network cable while leaving the power cord open. Recommended screws to use are 5x20MM and 5x15 Panhead Machine Screws and you can buy them in any hardware. Use a metal scrubber to remove all of the thermal junks on the heatsinks. Fortunately, now that there are online tutorials that will actually teach you to repair electronics including game consoles, the internet is also having tutorials on Xbox 360 repair.
Afterwards, try checking if the repair works by plugging it on the AV power cable and plugging the console on the RF board. Accordingly, one of the most common methods in resolving the Red Ring of Death is using the towel trick. After about few seconds, turn the power on again and have the game box wrapped in 3 or more towels. The first thing you have to do is removing the heatsinks of the game console by taking off the two x shaped clamps that holds the motherboard. Reinstall the screws on their respective places and make sure that they are not too tight or too loose. Once the heatsinks are removed, all the other parts should be separated from the metal case and the motherboard placed in a clean place. If not then you have to shell out some money and find a person who can fix your console.You are having a good time with your Xbox and with just few seconds away from finishing your game when suddenly the dreaded Red Ring of Death started flashing. If you do not have this kind of drill you can also use a hand drill to make the holes bigger.
コメント